SaniCom 1 For Kitchen And Laundry Installation With 2 Inlets


100 in stock

To check if this item qualifies for a discount Log In or Create an account.

The Sanicom 1 drain pump is used to pump gray water away from a variety of fixtures in commercial and residential applications.


Pay over 3 EQUAL zero-interest instalments of R5,224.10 with PayJustNow.
Find out how...

PayJustNow is a simple, easy-to-use payment system.

Here’s how it works:

PayJustNow allows you to pay for your purchase over 3 equal, zero interest instalments. You’ll pay one instalment at the time of purchase, the next at the beginning of the following month and the last one a month thereafter.

Step 1:

Browse your favourite online stores and proceed to check-out.

Step 2:

Choose PayJustNow as your payment method.

Step 3:

Create your account as easily as if your eyes were shut (though we’d recommend you keep them open).

Step 4:

Complete your purchase and whoop for joy!

Here’s what you’ll need:

  A valid RSA ID document

  To be over 18 years old

  An email address

  A SA Bank issued debit or credit card

R15,672.29 Incl.

100 in stock

Credit Options

The Sanicom 1 drain pump is used to pump gray water away from a variety of fixtures in commercial and residential applications. The system is able to discharge the waste up to 25 feet vertical and/or 250 feet horizontal. This model was designed to sustain the toughest applications from commercial applications where hot water can be an issue as it is capable of handling up to 194°F.

The Sanicom 1 model was designed to sustain the toughest applications meant for gray water pumps.  Its pumping capabilities and unique design are the reason why this range of pumps are preferred for heavy-duty applications.

The inside of the Sanicom 1 comprises a pressure switch and a circuit board assembly, which starts and stops the unit, a powerful 1-HP motor, which in turn starts the motor.

The motor is sealed for life in an oil-filled enclosure.  A spindle/shaft drives the impeller and therefore the moving parts are kept to an absolute minimum.  Water enters the chamber and is pumped away into the sanitary sewer.

The unit pumps the effluent upward to 25 feet and/or 250 feet horizontally (with gravity fall).  Once the water is discharged and the water level in the container goes down, the pressure switch deactivates the unit until water enters the unit again.  A normal operating cycle for the Sanicom 1 can be as short as 2 – 10 seconds depending upon the discharge pipe run configuration; power consumption is therefore minimal.

The Sanicom 1 handles up to 194°F water, making it perfect for commercial kitchen applications where dishwashers must operate at exceptionally high temperatures to meet health and sanitation standards. In addition, the unit is specially designed to withstand liquids with highly acidic properties, such as wastewater from processing applications. It’s important to use the proper pipe rated for high temperature on the discharge as well as for the inlets.

The wastewater from other sanitary fixtures is discharged into the Sanicom 1 via two 2-inch inlets, on either side of the housing. The discharge elbow on top of the Sanicom1 can be turned either to the left, to the right, or towards the back, depending on the discharge installation. A non-return valve, provided with the system, prevents backflow into the unit.

This unit has been designed with a vent connection on top of the enclosure.  All plumbing codes require a connection to a vent system. Please note that the vent system should be a two-way air vent.  The use of mechanical vents, air admittance valves, or similar devices is not permitted as these are considered one-way air vent systems.

It is also highly recommended for the gray water pump to be connected to a Ground Fault Interrupter (GFI) circuit.

The Sanicom 1 has been certified to American and Canadian Standards.  US: CSA Certified & IAPMO (UPC) listed – ASME A112.3.4, CA: CSA B45.9 / UL778 6th Ed / PS 52-2009e1

SKU: COM1 Category:
Weight 10 kg
Dimensions 41.9 × 23.2 × 33.17 cm


Additional Specifications

  • Weight:b22 lbs.
  • Inlets (in): 1 1/4” (top) 2” (side inlets)
  • Power supply: 120 V – 60 Hz
  • Shower/bathtub base min-height: 10″ min
  • Noise level (measured at 3 ft.): ≤ 68 dBA
  • Horizontal discharge: 250 ft
  • Vertical discharge: 25 ft
  • Amperage (Amps): 10 Max
  • Operating maximum temperature: 194 F°
  • Discharge pipe diameter: 1″
  • Tank volume: 2.75 gallons
  • Method of activation: Pressure switch/circuit board
  • Discharge Rate at 3 ft: 33 gal/min (124 liters/min)
  • Discharge Rate at 25 ft: 17 gal/min (64 liters/min)
  • Motor Speed (RPM): 3500
  • Motor: 1 HP oil-filled thermally protected motor
  • Capacitor rating (microfarad): 45
  • Power cord length (in): 50
  • Shut off the head (ft): 53
  • Normal running time”: 4-6 sec (short bursts)
  • Certifying agencies: CSA (IPC, NSPC)